Follow

One of the fist steps taken by the Lean Company is to introduce multidisciplinary teams (including operators) on the factory floor to help reduce waste.

Owner: beskidek

Listed in: Business

Language: English

Tags: kaizen, kanban, muda, lean manufacturing, smed

Report it


Site Statistics

Unique Visitors Today:
0
Page Views Today:
0
Unique Visitors this Week:
0
Page Views this Week:
0
Unique Visitors this Month:
0
Page Views this Month:
0
Total Unique Visitors:
5,853
Total Page Views:
7,425
Total Hits Out:
133
Traffic Chart

Latest Blog Posts for Lean Manufacturing

  • Calculations for OEE and TEEP
    on Jan 2, 2010 in OEE TEEP Quality
    What follows is a detailed presentation of each of the six OEE / TEEP Metrics and examples of how to perform calculations. The calculations are not particularly complicated, but care must be taken as to standards that are used as the basis. Additiona...
  • What is OEE?
    on Jan 2, 2010 in OEE TPM TQM jit
    - OEE or Overall Equipment Effectiveness is a system of measures that provide continuous visibility to manufacturing productivity and waste. - OEE provides a clear focus on utilization of facilities and equipment. - OEE is accepted worldwide as the s...
  • Overview of the System of OEE Metrics
    on Jan 2, 2010 in OEE TPM TEEP
    What is OEEIn the most general sense, OEE (Overall Equipment Effectiveness) can be described as a universally accepted set of metrics that bring clear focus to the key success drivers for manufacturing enterprises. The OEE strategy is considered “b...
  • What is SMED?
    on Dec 17, 2008
    SMED, stands for Single-Minute Exchange of Die, is a theory and techniques for performing setup operations in under ten minutes, i.e., in a number of minutes expressed in a single digit. The SMED method was revolutionized by Mr. Shingo since 1950 in...
  • Lean-Manufacturing Objectives
    on Nov 9, 2008
    QualityIncreasing the quality level of the working process means reducing the number of errors, repairs and rejects. The result is less demand for company resources and therefore lower total operating costs. CostThe production process begins with hum...
  • Reduce Waste
    on Nov 9, 2008 in muda
    1 - Muda caused by inappropriate processingUsing small front-picked containers reduces the length of the line, saving on general expenditure, reducing flow costs and saving time.2 - Muda caused by defectsDefects cost the company money and time. They...
  • Benefits
    on Nov 9, 2008 in andom jit just in time
    You would cut delivery times significantly, at the same time as reducing your stocks.You would halve the volume of rejects. You would to achieve almost 100% reliable delivery times.You would improve machine availability by 60% with no additional inve...
  • HistoryAt the end of 1890, Frederick W Taylor became the first to study work management scientifically and distribute the results. His work led to the formalization of time and motion studies and the setting of common standards. Frank Gilbreth then added th...
  • Lean Manufacturing identifies 7 areas of waste or ' muda '.
    on Nov 9, 2008 in muda standardise work kaizen
    The Lean Manufacturing house can only grow if its foundations are built first. Without using a highly flexible and modular system that allows muda to be eliminated and Kaizen attitudes to be introduced into the plant, it is impossible to proceed to t...
  • Changing the production systemThere are three problems inherent in any production system:• Waste (Muda),• Instability,• Variability (Mura).These problems reduce system efficiency by exerting a negative effect on quality, costs and delivery times. The end result is a lower r...
Loading Comments...

Comments

{ds_PageTotalItemCount} commentcomments
{pvComments::date}
{pvComments::comment}

Post a Comment

Close